This is a pattern and sewing tutorial to make a boxy top with frilled sleeves also called flute sleeves. A small embroidery border design is  given at the bottom edge on the front. 

Step 1. Cut out the pattern pieces.

You need  – Front pattern (& optional  lining ) ; back pattern (& optional  lining) ; sleeves and the frills

I am using artificial silk fabric which is quite thin, so I used the same fabric as lining and used this lining  as facing (Checkout the post on making facings for the alternate way if you are not using lining) ; So cut all the pieces both front and back in duplicate.

Pattern for the bodice

The white line shows the markings for the front bodice. First cut both the fabric pieces as per the back pattern; then remove one piece and then mark the front pattern on the remaining one

A-B = 20″ ( length of top) You can take this measurement from shoulder to where you want the top to end preferably where you tie the skirt or the pant belt plus 1.5 ” seam allowance
A-O = 3.5″ This is the neck width.
A-N (Back neck) =2″ Mark down from A

N-M = 4″ – This is for the back neck slit for hook

O-L = 5-6″ -This is the neck depth for the front neck. 5 inch will give a Tshirt type close neck.

A-E = 7.5″ This is the bust line Mark down from A.
E-D = 1/4 of Bust round + 1.5″ This is marked on the bust line

A-F = 1/2 of shoulder to shoulder + 1/4″ ( take measure from shoulder point to shoulder point and half it)

F-G= 1/2″. This is marked for the shoulder slope

Mark down straight from F to the bust line
H-J = 1″. From H Mark diagonally to J
H-I= 1″. From H mark to the inside 1″ to I – this is for marking the front armhole line
I-K=1″. Mark diagonally to K 1″

Mark the front neckline as D-K -G & back neckline as D-J-G

The bottom edge of the bodice is marked straight down from the bustline. This is assuming that your bottom edge is smaller than the bust round. As it ends on the waist area for those who have a big waist round this top maynot be right – checkout this tip and others like this in the post dressing tips to make yourself look thinner.

When cutting you can give a slight upward curve at C (1/2″) so that it doesnot hang down. 

Pattern for sleeve

Make a pattern for the sleeve . You can follow the pattern in this page for drafting sleeves. or the pattern below

Fold the fabric pieces for the sleeves right sides together . Mark the back sleeve pattern. Cut through the line. Open it up and cut through the front sleeve line on one side.

Step 2

Finish the necklines of front and back bodices.

I have kept the top fabric and lining fabric rightsides together, drew the  neckline markings and stitched through the marking

Turn the lining to the other side and press in place.

Step 3. Stitch the shoulder seams

Start stitching from the center aligning the center line of sleeves with the shoulder seam

Now sew the side seams . Sew the sleeves and the bodice side seams of two sides.

Step 5 Make the frills for the sleeves

Measure the sleeve bottom edge round ( without the seam allowance). Take this as X. Divide X by 6.28. Take the result you get as Y

Take two pieces of fabric (for one sleeve) of 20 inch width and 10  inch length. Fold by the center.

Join two half cirlces to make one circle. Finish the seams with a zig zag edge. ( because when you lift the arms this will be seen)

Step 6 Do the embroidery

A professional would do this work before any sewing is done, after the pattern is marked and in a hoop – But I am not a professional; so excused. But you can be one and do it the proper way. Use interfacing on the back for the embroidery to have some stability .

I have done chicken scratch embroidery. You can do  any other embroidery border designs as well

Usually this embroidery involves making double cross stitch  on checkered fabric (gingham). I have drawn similar markings 1/2 inch apart to make the double cross stitches . These cross stitches are then looped with a blunt needle and thick thread in a pattern. There are many ways that you can do this work.Checkout the chicken scratch embroidery tutorial for more details

Step 7 Attach hook on the back and make a thread bar as well.Read How to sew hooks  and eye if you would like to know how to. 

Related posts : Cap sleeve sewing tutorial; Names of all tops; How to sew a simple tunic top ; Halter top pattern